Door Frames
If a door frame needs to be cut, use a piece of plank to obtain the correct height. 

Saw door frames and architraves to the require height allowing for 2 mm of space to the planks. 

Moisture Protection 

All types of concrete subfloors require insulation against moisture.
This includes types with built-in moisture barrier, ceramic, heated and covered with resilient floors. Use a PE moisture barrier film with a minimum thickness of 0.2 mm (.008’’). On ground and basement subfloors we recommend to lay 2 layers crossways for better moisture protection.

Lay the PE film, allowing for at least 20 cm (8'') overlapping and tape.
Turn the film upward 5-cm along the walls. Trim after the skirting boards are fixed. 

Measure the room accurately, at right angle to the direction of the planks. The planks in the final row should be at least 5 cm wide.
If necessary, the planks in the first row can be cut to a smaller size

Turn the tongue side of the plank facing the wall. Maintain a gap of 10 mm on the short side. Adjust the lengthways gap from the wall once 3 rows of planks have been laid. 

If you are installing Wood floors with three strips, try not to match the strips of the tiles. 

Turn the tongue side of the plank facing the wall. 
Maintain a gap of 10 mm on the short side. 
Adjust the lengthways gap from the wall once 3 rows of planks have been laid.

Hold the next plank against the first at an angle to the first one and lay it flat on the floor. Complete the first row in the same way. 

Cut the final plank of the first row to the correct length

If you are installing floating floor planks, start the next row with the piece left over (must be at least 300 mm long). Always ensure that the end joints are staggered at least 300 mm.

If you are installing CorkComfort Floating tiles with 605 x 445mm, brick or half brick installation method  should be used.

Place the final plank face down and the short side without the locking strip towards the wall. The distance to the wall should be 10 mm.

Mark where the floorboard is to be cut. Place the plank face down on the work surface and cut to size using a padsaw. Use a fine toothed type if you are using a handsaw. In this case, cut the planks face up.

Use a cut piece of plank from the previous row to start the next row.
This must be at least 30 cm long. If the piece is too short, start with a new board and cut it in half. Always ensure that the end joints are staggered at least 30 cm. 

Place the first plank of the new row with the tongue side at an angle against the groove side of the plank in the previous row. Press forward and lay it flat at the same time.

Place the short end of the plank at an angle against the previous installed plank and fold down. Ensure that the board is positioned on the integral locking strip of the floorboard in the previous row.

Lift floorboard (together with the previous laid in the same row) lightly up (about 30 mm), push it against the row in front and then put it down.

Tip: This movement requires some gentle adjustments on the pressing angle. Adjust the distance to the wall to 10 mm when three rows are completed.

Proceed the installation as described above until reaching the opposite wall.

Sometimes the first row must be cut to match an uneven wall. Transfer the shape of the wall to the planks. Do not forget to allow 10 mm for the expansion gap.

To remove the first row, lift the plank a few centimetres and tap along the joint. Cut the planks as required.

Measure and cut the planks in the last row to size. Allow for 10 mm distance to the wall. No plank should be less than 5 cm width. 

The last and first plank can be cut in the correct width. Place the last plank on top the second to last plank. Mark the plank  with the help of a piece of plank without locking the strip. Allow for 10mm distance to the wall for the expansion gap. 

The holes should be 20 mm greater than the pipe diameter. Saw as shown in the picture. Glue the sawed piece back into place. Cover the hole with a pipe sleeve.

If you wish to remove the flooring, just lift the planks a few centimetres and tap along the joint.

The released plank can then be pulled out. Never bend connected plank backwards, as this will damage the planks.

If you cannot angle the tile under e.g. a doorframe or low fitted radiator, you can do as the picture shows: cut away the locking edge. 

Glue (PVA Glue, class D3). Install the plank